It can be dangerous to work with electric and gas water heaters. Because of this reason, it is important that all repairs should always be carried out by a licensed and qualified water heater specialist. Failure to do so can cause you to violate several building codes and local regulations.
Many of us know that a water heater is an important appliance since it produces enough hot water for the entire household. Cold water enters the tank and eventually heated properly after waiting for a couple of minutes. You can now use this warm water for taking showers, cleaning dishes and washing clothes.
Hard water mineral deposits can form at the bottom of the tank if you don't flush and drain them regularly. You may notice them accumulating in a honeycomb fashion, resulting to poor water heater efficiency. Once the sediments get too heavy for the tank to handle, the volume of water that can be stored will eventually be limited.
Prepare your tank first before draining. Turn off the circuit breaker or gas valve supply to prevent accidents from happening while you work on your heater. Do not forget to shut down the water supply to stop water from entering the tank during the repair process. To avoid scalding your skin, wait for a couple of minutes until the water cools down. You can also turn the water heater the night before you drain it. Doing these steps should protect you from unfortunate fatal accidents.
Connect a standard hose to the drain valve and place the other end to a secure drainage. Open the drain valve to release the water until the tank is empty. Disconnect the hose and place a bucket below the valve to catch the remaining sediments inside. Open the cold water supply to flush the hard water mineral deposits and close the drain valve until the water runs clear. Refill the tank first before switching the unit on.
If you think the water running in your taps isn't too hot, there are several factors you need to check into. If you have an electric unit, check the circuit breaker. It is possible that no power is getting to the unit if it's tripped. Simply reset the breaker to solve the problem.
You can also check the upper heating element of your water heater to check if it's receiving power. Use a multi-meter to check it and reset when needed. You may need to replace the thermostat if the cold water continues to flow in your hot water pipes. Do not forget to shut down your power and water connections before replacing it.
There are other water heater problems that you may encounter in the long run. Just remember that when the issue gets out of hand, call a specialist immediately. Performing repairs on your own without professional help can put your life at risk and worsen the situation. Prevent this from happening by calling a specialist as soon as the problem arises.
Many of us know that a water heater is an important appliance since it produces enough hot water for the entire household. Cold water enters the tank and eventually heated properly after waiting for a couple of minutes. You can now use this warm water for taking showers, cleaning dishes and washing clothes.
Hard water mineral deposits can form at the bottom of the tank if you don't flush and drain them regularly. You may notice them accumulating in a honeycomb fashion, resulting to poor water heater efficiency. Once the sediments get too heavy for the tank to handle, the volume of water that can be stored will eventually be limited.
Prepare your tank first before draining. Turn off the circuit breaker or gas valve supply to prevent accidents from happening while you work on your heater. Do not forget to shut down the water supply to stop water from entering the tank during the repair process. To avoid scalding your skin, wait for a couple of minutes until the water cools down. You can also turn the water heater the night before you drain it. Doing these steps should protect you from unfortunate fatal accidents.
Connect a standard hose to the drain valve and place the other end to a secure drainage. Open the drain valve to release the water until the tank is empty. Disconnect the hose and place a bucket below the valve to catch the remaining sediments inside. Open the cold water supply to flush the hard water mineral deposits and close the drain valve until the water runs clear. Refill the tank first before switching the unit on.
If you think the water running in your taps isn't too hot, there are several factors you need to check into. If you have an electric unit, check the circuit breaker. It is possible that no power is getting to the unit if it's tripped. Simply reset the breaker to solve the problem.
You can also check the upper heating element of your water heater to check if it's receiving power. Use a multi-meter to check it and reset when needed. You may need to replace the thermostat if the cold water continues to flow in your hot water pipes. Do not forget to shut down your power and water connections before replacing it.
There are other water heater problems that you may encounter in the long run. Just remember that when the issue gets out of hand, call a specialist immediately. Performing repairs on your own without professional help can put your life at risk and worsen the situation. Prevent this from happening by calling a specialist as soon as the problem arises.
About the Author:
Looking to find out more about water heater replacement , then visit www.waterheaterrepairfriscotx.com to find the best water heater specialists for your needs.
0 comments:
Post a Comment